Ohio Flint Tumbling Rough
Easy-to-polish. A great rough for beginners.
This photo shows some of our rough Ohio Flint. The rough in the photo above is wet to show full color.
This photo shows numerous tumbled stones that we tumbled from the same batch of Ohio flint shown above, using the Rock Tumbling Recipe shown on this page.
Ohio Flint Tumbling Rough
, , and What do they mean?
Size:Small pieces - mostly 3/8 to 1 1/2 inches - for small tumblers
Ohio Flint is one of our favorite rocks for tumbling. We like it because it produces colorful tumbled stones, marked with interesting patterns. The material sold here is small pieces of a white to gray flint, marked with black bands, and splashed with patches of red, orange-brown, and sometimes yellow.
This rough is a hard and tenacious material that shapes slowly in a tumbler - but that durability enables it to be polished to a very bright luster that even a beginner should be able to achieve in a small rotary tumbler such as the Thumler's MP-1, A-R1, and A-R2.
We rate this rough as an easy rock to tumble.
"Ohio Flint" is a name used for opaque chalcedony found at several locations in central Ohio. Native Americans started mining Ohio Flint at the end of The Great Ice Age. They used it to make knife blades, scrapers, tools for impact and grinding, projectile points and much more. Learn more about Ohio Flint here.
Did you know that Ohio Flint was named the official gemstone for the state of Ohio by the Ohio General Assembly in 1965? Today, jewelry artists use Ohio Flint tumbled stones, cabochons, and beads to craft beautiful jewelry.
This mix is perfect for the beginner. It rounds nicely in the tumbler and accepts a brilliant polish with TXP aluminum oxide polish. It has a range of particle sizes from about 3/8" (9 mm) to 1 1/2" (38 mm) and requires little to no preparation.
EASY Rock Tumbling Recipe:
Ohio Flint (3/8 to 1 1/2 inches)
This Ohio flint has been crushed and sized to perform well in small rotary tumblers such as the Thumler's MP-1, A-R1, and A-R2. The size range gives the material a good tumbling action and eliminates the need for ceramic media. Our EASY Rock Tumbling Recipe works well for rough that has a Mohs hardness of 7 and has been crushed to a variety of particle sizes under about 1 1/2 inches.
Recipe for Rotary Tumbling
Coarse Grit Step:
Fill your tumbler barrel about 2/3 full of rough. Then add 2 tablespoons of coarse (60/90) grit per pound of material in the barrel. Add water to just below the top of the rocks. Run the material in coarse grit for 1-2 weeks. One week in coarse grit will give you good results. However, we feel that two weeks in coarse grit gives you much better results.
At the end of each step in the rock tumbling process, make sure to clean your rocks and barrel to reduce the chance of coarser grit contaminating the finer grit steps.
Medium Grit Step:
Put your cleaned rough back into the barrel. Then add 2 tablespoons of medium (150/220) grit per pound of material in the barrel. Add water until it is just below the top of the rocks. Let it tumble for one week.
Fine Grit Step:
Barrel slurry dumped down the drain will harden like concrete.
After clean-up, put the rocks back into the barrel using 2 tablespoons of fine grit per pound of material. Again add water to just a little below the top of the rocks. Tumble for one week. The rocks should now be smooth and possibly starting to get a slight luster.
IMPORTANT: Make sure that your barrel and rough have been cleaned thoroughly. Any grit carried over from a previous step will likely ruin your polish. Place the rough in the barrel with two tablespoons of TXP polish for each pound of material in the barrel. Add enough water to almost cover the rocks and let it tumble for one week.
Burnish If Needed:
Ohio flint usually takes a great polish. However, burnishing this material after the polish step can often improve the shininess of the finished stones. If you would like to try burnishing to see if it improves the look of your polished stones, full burnishing instructions can be found here.
EASY Vibratory Tumbler Recipe:
3/8" to 1 1/2" crushed rough
Coarse Grit (60/90 Mesh):
Coarse grit is not used in a vibrating rock tumbler.
Medium Grit (150/220 Mesh):
Ceramic media is not required; however, we always run at least 20% ceramic media in a vibratory tumbler because we believe that it improves the tumbling action and results in nicer tumbled stones.
After you have your bowl loaded to the manufacturer's recommended level, add 1 tablespoon of grit for every two pounds of material, including the media, in the bowl. While the tumbler is running, slowly add water until the material has a thin coat of wet grit and the tumbling action is smooth and fast in the bowl.
Check the bowl every 8-12 hours to ensure the action is still good. If the action has slowed, add water a little at a time until the action is back to normal. If the mud gets too thick, you will need to do a complete rinse of the material and bowl. After rinsing, add fresh grit and water and start tumbling again. You are done with medium grit when you are satisfied with the shape and smoothness of the stones. Usually 4-6 days for us with this material. Give the material and bowl a thorough cleaning before moving on to fine grit.
Fine Grit (500F Mesh):
Place your material back in the tumbler bowl, then add enough polished ceramic media to bring the load up to the manufacturer's recommended operating level. Add one tablespoon of polish for every two pounds of material in the bowl. Then, turn the tumbler on and slowly add water until the material has a thin coat of wet grit and the tumbling action is smooth and fast in the bowl.
Open the bowl every 8-12 hours to check the action is still good. We usually run fine grit for 48 hours. Thoroughly clean the bowl and material before moving to the polishing step.
Polish (#61 Rapid Polish or TXP):
Make sure that your barrel and rough have been cleaned thoroughly. Place the cleaned material back in the bowl. If needed, add ceramic media that has been previously polished, to bring the bowl up to the manufacturer's recommended operating level. Add one tablespoon of polish for every two pounds of material in the bowl. Turn on the tumbler and slowly add water. Stop adding water when the material has a thin coat of wet polish and the tumbling action is smooth and rapid.
Like the previous grit steps, open the bowl every 8-12 hours to check the tumbling action. Add water if it has slowed. We have found that 48 hours is usually all the time you need to get a good polish in a vibratory tumbler. Any more time than that and you run the risk of damaging / bruising the material.
Burnish If Needed:
Ohio flint usually takes a great polish. However, burnishing this material after the polish step can often improve the shininess of the finished stones.
Customers also bought...